刮板输送机中板仿生耐磨优化试验研究

刮板输送机中板磨损失效已成为输送机运行故障的主要原因之一，为了提高中板耐磨性，基于蜣螂非光滑单元进行了仿生中板设计，以磨损量为响应值，进行了单因素和响应面法优化试验。根据响应面法试验结果得到的因素显著性影响顺序（从高至低）依次为：径向距离，深径比，直径，节距角。基于试验结果建立了磨损量与因素的回归预测模型，经试验对比发现，预测模型与真实试验的相对误差为3.2%。在特定工况（煤散料粒度为6~8 mm、载荷为20 N、刮板链速为0.65 m/s及试验时长为6 600 s）下，当深径比为1.41、直径为0.69 mm、节距角为6.55°和径向距离为4.66 mm时，磨损量最小，仿生中板的耐磨性提高了12.6%。分析其耐磨机理发现，与光滑板相比，仿生板的磨粒磨损及黏着磨损较轻。凹坑分布可破坏持续切削中板表面的煤粒运动状态。中板的仿生优化可为今后刮板输送机的设计提供一定参考。     

电压对电刷镀三价铬镀层性能的影响

在45钢表面电刷镀得到三价铬镀层,镀液组成和工艺条件为:Cr2(SO4)36H2O 0.4 mol/L,甲酸铵0.5 mol/L,氨基乙酸0.5 mol/L,H3BO30.6 mol/L,NaH2PO2 H2O 0.3 mol/L,pH=1.5,温度50°C,镀笔移动速率15 cm/s。研究了电压对镀铬层显微结构、表面粗糙度、厚度、显微硬度和耐磨性的影响。随电压增大,镀层厚度增大,显微硬度和耐磨性均先提高后降低。电压为14 V时,镀层的表面平整,粗糙度为2.387μm,显微硬度为602 HV,耐磨性最好。     

A novel combination of precursor pyrolysis assisted sintering and rapid sintering for construction of multi-composition coatings to improve ablation resistance of SiOC ceramic modified carbon fiber needled felt preform composites

A double-layer coating composed of MoSi₂–SiO₂–SiC/ZrB₂–MoSi₂–SiC was designed and successfully constructed by a novel combination of precursor pyrolysis assisted sintering and rapid sintering to improve the ablation resistance of SiOC ceramic modified carbon fiber needled felt preform composites (CSs). The ZrB₂–MoSi₂–SiC inner layer coating was in relatively uniform distribution in the zone of 0–3 mm from the surface of CSs through the slurry/precursor infiltration in vacuum and SiOC precursor pyrolysis assisted sintering, which played a predominant role in improving oxidation and ablation resistance and maintaining the morphology of CSs. The MoSi₂–SiO₂–SiC outer layer coating was prepared by the spray and rapid sintering to further protect CSs from high-temperature oxidation. The ablation resistance of CSs coated with double-layer coating was evaluated by an oxygen-acetylene ablation test under the temperature of 1600–1800 °C with different ablation time of 1000 and 1500 s. The results revealed that the mass recession rates increased with the rise of ablation temperature and extension of ablation time, ranging from 0.47 g/(m²·s) to 0.98 g/(m²·s) at 1600–1800 °C for 1000 s and from 0.72 g/(m²·s) to 0.86 g/(m²·s) for 1000–1500 s at 1700 °C, while the linear recession rates showed negative values at 1700 °C due to the formation of oxides, such as SiO₂ and ZrO₂. The ablation mechanism of the double-layer coating was analyzed and found that a SiO₂–ZrO₂–Mo_4.8Si₃C_0.6 oxidation protection barrier would be formed during the ablation process to prevent the oxygen diffusion into the interior CSs, and this study provided a novel and effective way to fabricate high-temperature oxidation protective and ablation resistant coating.     

The improvement of the self-healing ability of MoSi2 coatings at 900–1200 °C by introducing SiB6

The brittleness of MoSi₂ ceramic and the thermal mismatch between MoSi₂ coating and C / C composite lead to brittle cracking of the coating at 900−1200 °C. This problem has been overcome in this studyby introducing submicron-SiB₆ into the coating. The pre-fabricated cracks and a kinetics model of hot-pressed SiB₆-MoSi₂ ceramic could quantitatively predict the glass growth and crack healing. As expected, enhancing temperature and SiB₆ content increased the growth rate of the borosilicate glass and the crack healing ability of MoSi₂ ceramic, which was ascribed to the lower oxidation activation energy and larger specific surface area of submicron-SiB₆. For the plasma sprayed coating, SiB₆ with submicron structure was benefit for cracking inhibition and formation of borosilicate glass during oxidation, reducing the oxygen permeability and the consumption of inner coating. Hence, the 15 % SiB₆-MoSi₂ coatings raised the protection times to 84 and 120 h at 900 and 1200 °C respectively, presenting favorable oxidation protective performance.     

300M超高强钢在中性盐雾环境中的腐蚀行为及机制

摘要：为了研究300M超高强钢在中性盐雾环境中的腐蚀行为及腐蚀机制，采用失重法，宏观、微观腐蚀形貌分析，三维表面轮廓分析及电化学分析的研究方法，来表征腐蚀实验现象并进行分析。结果表明：300M超高强钢在中性盐雾环境中的腐蚀产物为FeOOH、Fe2O3、Fe(OH)3和Fe3O4；腐蚀速率随着腐蚀时间逐渐降低，腐蚀后期（72h）腐蚀速率降低50%；腐蚀初期以点蚀为主，点蚀坑通过横向扩展，逐渐发展为后期的均匀腐蚀，腐蚀表面形貌呈沟壑状；外腐蚀层对基体的保护能力很弱，Cr元素在锈层靠近基体的一侧偏聚使内腐蚀层具有一定的抗腐蚀性。     

镁改性活性炭强化活性污泥处理混合污水研究

基于序批式活性污泥法(SBR)工艺,将镁盐改性活性炭(MgO-PAC)与传统活性炭(PAC)混合而成MPAC材料,用于处理生活与工业混合污水。通过连续30 d的运行实验,探讨了MPAC材料对生活与工业混合污水中COD、NH4^+-N和TP的去除效果以及对污泥的比耗氧速率、沉降性能和微生物多样性的影响。结果表明,投加MPAC材料对污水中COD的去除率提升了12.7百分点,对TP的去除率提升了17.5百分点,对NH4^+-N的去除率超过86.4%。投加MPAC后处理效果更好的重要原因,在于MPAC使得活性污泥的沉降性能和比耗氧速率得到明显改善,也提升了污泥的微生物丰度。MPAC对活性污泥处理生活与工业混合污水具有强化作用。     

Effects of corrosion in liquid fluoride salt on the tensile strength of domestic SiC fibers

The relationship between the tensile strength of corroded domestic second-generation (2ed-gen) SiC fibers at various temperatures for 500 h in 46.5LiF-11.5NaF-42.0KF (mol. %) eutectic salt and the typical microstructure was studied. Weibull theory was used to analyze the critical defects that caused the tensile fracture, and the microstructure of fibers before and after corrosion was characterized. It is concluded that the decrease of tensile strength after corrosion at 800 °C is caused by the surface injury of fibers, which led to the shift of critical defects from the internal defects of virgin fibers to surface defects. Moreover, corrosion at higher temperature accelerates the corrosion process and dissolve the surface O-contained layer thoroughly. This shifts the critical defects back to the internal defects and will be helpful for the recovery of tensile strength of corroded fibers at the higher temperature.     

Fire hazard in transportation infrastructure: Review,assessment, and mitigation strategies

This paper reviews the fire problem in critical transportation infrastructures such as bridges and tunnels. The magnitude of the fire problem is illustrated, and the recent increase in fire problems in bridges and tunnels is highlighted. Recent research undertaken to address fire problems in transportation structures is reviewed, as well as critical factors governing the performance of those structures. Furthermore, key strategies recommended for mitigating fire hazards in bridges and tunnels are presented, and their applicability to practical situations is demonstrated through a practical case study. Furthermore, research needs and emerging trends for enhancing the “state-of-the-art” in this area are discussed.     

Characterization of anisotropic gas permeability and thermomechanical properties of highly textured porous alumina

Porous alumina with a highly textured microstructure was fabricated by pulse electric current sintering (PECS) using alumina platelets. Highly oriented porous alumina with a porosity of 3%–50% was obtained by a pressure-controlled method of PECS. The properties of the highly textured porous alumina were measured in two directions. The nitrogen gas permeance and thermal conductivity at room temperature were higher in the direction along the platelet length due to the higher continuity of pores and the connectivity of alumina platelets, respectively. The anisotropy of the thermal conductivity at room temperature was investigated and explained by the effect of grain size of platelets as well as morphology and orientation of pores. The bending strength was higher with the loading direction along the platelet thickness. The thermal shock strength was clearly different in the two directions. The difference in the thermal shock strength was investigated by the measurement of properties and thermal stress analysis.